Power Amplifier

By Range

By Type

Product Reference Information

Behind The Badge

Supplied With

The NAP 500 includes:

Suggested System

A Naim Retailer will recommend the right system for you, however you may choose to partner the NAP 500 with the following as a start:

  • Separates System
  • CD555
    CD555
  • 555 PS
    555 PS

    555 PS is the dedicated power supply for CD555

  • NAC 552
    NAC 552
  • 552 PS
    552 PS

    552 PS is the dedicated power supply for NAC 552

  • Ovator S-600
    Ovator S-600
Download PDF

NAP 500 Power Amplifier

NAP 500
  • NAP 500
  • NAP 500
  • NAP 500
After seventeen successful years at the top of Naim's amplifier range, the NAP 135 was eclipsed by the flagship NAP 500. Our design brief for the NAP 500 required an amplifier that could drive any load down to 2 Ohms for prolonged periods, deliver over 100W into 8 Ohms and sound - at the very least - as good as our reference at the time, the NAP 135. Needless to say, every aspect of the NAP 500's sound quality is truly exceptional.

To avoid the compromises implied by the use of multiple sets of output devices, either in totem-pole or parallel configuration, the search was on for a very special output transistor. A bipolar transistor with a specific combination of very high current, power rating and bandwidth was needed, far in excess of anything available to Naim before. A suitable output device was eventually developed after six years' collaboration with a semiconductor manufacturer.

From an early stage of conception it was decided to use bridged amplifiers for each channel of the NAP 500. This allowed the design to have maximised open and closed loop speed, less intrusive protection circuitry and reduced interaction between input and output signals as the very high drive currents to the loudspeaker do not flow through the system earth.

Naim has always understood the importance of reducing supply-induced intermodulation distortions and mains harmonic electrical noise from an amplifier, and has always used regulated supplies in its premier amplifiers. It was considered likely that improvements in these areas would yield further large gains in performance. Each channel of the NAP 500 includes ten stages of local regulation. To reduce interference from the mains supply further, the transformer and first stages of the power supply are in a separate enclosure (the same size as a SuperCap), which provides twelve raw D.C. supplies for the power amplifier. Hence, the NAP 500 system consists of two boxes, a stereo amplifier and a separate power supply.

All new circuit topology has been developed to maximise bandwidth and reduce distortions and power supply dependency. Also, special attention has been paid to reducing thermally-induced noise, an especially important consideration in power amplifiers. A variable speed intelligent fan system provides discreet extra cooling if needed.

The performance of the finished amplifier exceeds the design brief in all areas. Power output per channel is over 140W into 8 ohms and compared with the NAP 135, which in itself already provided exemplary measurements, the NAP 500 has five times the internal bandwidth, a quarter of the distortion and a one hundred times reduced operating noise floor.

AUDIO INPUTS
Analogue Inputs 2 x XLR
Input Impedance 18kΩ
AUDIO OUTPUTS
Gain +30dB
Frequency Response -3dB at 1.5Hz & 100kHz
SPEAKER OUTPUTS
Speaker Outputs L & R, 4mm “banana” sockets
Power Output 140W/channel, 8Ω
Transient 700VA
POWER
Power Supply Options 500PS
PHYSICAL
Dimensions 160 x 432 x 374mm (H x W x D)
Weight 25kg
Shipping Dimensions 270 x 570 x 520mm (H x W x D)
Shipping Weight 28.2kg
FINISH
Front Brushed and black anodised
Case Brushed and black anodised

MANUALS & DOWNLOADS

Here are all the items available for download that relate to this product. If the information you require is not featured, please contact Naim Customer Support.

.